How To Install Kingston Brass Kitchen Faucet?

As an Amazon Associate, I may earn from qualifying purchases at no extra cost to you. All the products recommendation links on izzysmarthomeguide.com will navigate to Amazon

Table of Contents

To be honest, installing a Kingston brass kitchen faucet isn’t a big deal even though you’re doing it for the first time.

Trust me, you can do it on your own even though you don’t have any plumbing experience.

However, you need to be very careful when making adjustments such as mounting as well as connecting the faucets.

In absence of proper adjustment, your faucet may begin to leak or show signs of other similar problems.

According to the Environmental Protection Agency, when a faucet drips once per second, up to 3,000 gallons of water gets wasted annually – that’s enough water for an average of 180 showers. If you reside in an area where water bills are high, you may not want to fix your kitchen faucet wrongly.

Steps Involved in Installing a Kingston Brass Kitchen Faucet

Let’s have a quick look at the steps involved in installing a Kingston brass kitchen faucet.

First thing first, make sure you flush both supply lines to clear any debris before you begin the installation, and then shut off both supply lines before flushing
The next thing that you need to do is to detach the Tee connector and spout mounting hardware from the spout
Now, it’s time to apply appropriate amount of silicone caulking around the middle hole at the sink top

Refrain from using plumber’s putty as it may ruin the finish as well as invalidate the warranty
The next thing that you need to do is to insert the spout base ring from the sink top if possible and most importantly, spout through the middle hole
Insert the spout setup hardware back onto the spout, and secure the locknut with your hands

Then, insert the popup rod through the back hole or the spout top, and then revolve the indented metal washer to ensure a smooth pop-up rod movement
Now its time to test the popup rod for ease of operation
Apply the teflon tape, then you need to place the tee connector washer and thread the tee connector onto the spout shank

Secure lower lock nut and place the washer into the cold and hot valve and then position them through the holes on the sides
While holding from below the sink, secure the top lock nut from above and set an appropriate height from the deck to the stem’s tip.
Secure both the top and the bottom lock nuts and make sure not to tighten the lock nut excessively as it may result in undue stress on the stern body causing leakage, which may result in water damage

Attach flexible hoses to the exit hot and cold valve assembly port; you may need to loop the hose but make sure you don’t overtighten.
On the all-male threading use a Teflon tape and attach the inlet supply lines to the lower inlet port of cold and hot valve connection
Fix the bottom gasket mounting nut onto the draining system; wrap the top drifted end of the draining system with Teflon tape

Apply silicone to the flange’s bottom side, Install the flange body up through the draining system, hold the draining system at the sink’s back, and screw up the mounting nut with your hands. Be sure to clean excess silicone
Place the pivot rod into the pivot rod vent, insert the pivot nut over the pivot rod, fix it on the draining system, and secure it firmly
Insert the pivot rod through one of the lift rod strap holes and tighten it with the spring dip.

Then adjust the lift rod height by resetting the clevis screw on the faucet with the lift rod in position through the lift rod strap, insert the lift rod and harden with a clevis screw
Once the connections have been made, check on the water supply to ensure no leaks; if no leakage, detach the aerator from the spout and turn the handles to a completely open position.
Allow the water to run for at least 30 seconds, then replace the aerator

Best Way to Take Care & Maintain Your Faucet

Most brass faucets are finished by unique standards.

Regardless, due to the high mineral content in water, your finish may get tarnished and dull with time.

In order to keep your faucet in a good health, the below-mentioned dos and don’ts will definitely help you.

Dos:

We recommend using silicone-based caulking when installing
Use a water solution and mild soap for cleaning your faucet

Make sure you dry the faucet after using it
Lastly, make a habit of waxing the faucet on a regular basis

Don’ts:

Use plumbers’ putty during installation
Use abrasive agents to clean

Caution:

Make sure that you’ve flushed out the water lines completely before use in order to get rid of clogs and debris in your water system that could lead to malfunction and water flow reduction
If you don’t flush out the water lines before using the new kitchen brass faucet, your warranty may become void
Using abrasive may destroy your faucet’s finish and invalidate the warranty

How Long Does It Take to Install a Brass Faucet?

The time needed to install a brass faucet depends on a wide range of tasks.

However, if you’re a professional or experienced DIYer then it shouldn’t take more than eight hours to install the kitchen faucet as long as all the necessary tools and materials are on set.

All tasks include preparing and protecting the area, removing an old faucet in case of a replacement, and fixing the brass faucet with new supply lines.

Benefits of Installing a Brass Kitchen Faucet

Let’s have a quick look at some of the important benefits of installing a brass kitchen faucet.

Durability

It goes without saying that brass faucets are more corrosion-resistant than all other materials on the market.

Moreover, if you’re dealing with hard water which is prone to corrode faucets rapidly then this is particularly important.

Hygiene

Many of you wouldn’t be aware of the fact that brass is germicidal which simply means it is capable of killing germs.

At the same time, you need to pay keen interest when purchasing a brass faucet since some are merely sealed with brass and might not serve the same purpose as those fully manufactured from brass.

Timeliness

Brass is one of few materials that have been used for a long time. Besides, it gives your kitchen a vintage appearance.

It’s A Wrap Up

First and foremost, I would like to thank you for being with us till the end.

Secondly, I would like to bring to your notice that I along with my core team have put loads and loads of effort into coming up with this idiosyncratic superlative piece of information.

And, in case, you liked our effort and want to appreciate us then please do share this post with like-minded people and the ones who are in search of it.

After all, sharing is caring, isn’t it?

Nowadays, there are so many faucet varieties; some are self-filtering, others have different streams, and others have a boiling water attachment. But you can never go wrong with a brass kitchen faucet.

A Kingston brass kitchen faucet revitalizes your kitchen. While it may seem like just a normal kitchen faucet, it creates a big difference in your house. By installing the faucet, it can greatly increase your satisfaction when performing everyday kitchen chores due to its great appearance.

[Related]